Flame Safe USA
Ph: + 1-817-740 -9197
email: [email protected]
2650 Warfield Ave., Fort Worth, TX 76106
Fire Retardant wood, fire retardant plywood, fire retardant lumber, millworks, wood specialties, I-Joists, MDF, OSB, particle board, T-111, fire retardant timbers
Dallas, Fort Worth, Austin, San Antonio, Houston, Waco, Odessa, Laredo, Brownsville, El Paso, Corpus Christi, Amarillo, Shreveport, Tulsa, Oklahoma , Dallas, , Plano, Frisco, Dallas County, Tarrant County, Abilene
Surface to be treated must be dry (up to 24 hours drying time after a rain and 4 hours after a dew). Surface must be clean. Brooming or air blowing may be necessary to remove leaves and needles. Apply Shingle Safe, by spray, DO NOT DILUTE. To maximize coverage start from the ridge down working your way across the roof surface. The sprayer tip should be held approximately 8" to 12" from the surface and at a 45 degree angle (or greater) to the roof surface. The angle will allow coverage underneath the leading edge of the shingle above. The specified application rate is 120 sq. ft. per gallon.
ASTM E108 - UL790
APPLICATION: Pressure wash roof to remove all foreign substances (fungi, molds, mildew, etc.) Be sure surface is clean and dry before treating. Apply with sprayer head held at 8 to 12 inches from surface. Treat all surface areas where possible. Do not expose treated area to moisture for 24 hours. Treat roofs by applying chemical to surface area and substructure area (attic), if possible
QUICK REFERENCE FOR APPLYING SHINGLE SAFE
COVERAGE RATE: 120 sq. ft. per gallon
Ft Worth, Dallas, Austin, Houston, TX, San Antonio, Oklahoma City, Tulsa, Shreveport, Montgomery, Alabama; Phoenix, Arizona; Los Angeles, California; San Francisco, California; Denver, Colorado; Bridgeport, CT; Washington DC; Miami, Florida; Atlanta, Georgia; Honolulu, Hawaii; Boise, Idaho; Chicago, Illinois; Indianapolis, Indiana; Des Moines. Iowa; Kansas City, Kansas; New Orleans, Louisiana; Baltimore, Maryland; Boston, Massachusetts; Detroit, Michigan; Jackson, Mississippi; Newark, NJ; Santa Fe, New Mexico; New York City, New York; Fayetteville, NC; Bismark, North Dakota; Tulsa, Oklahoma; Portland, Oregon; Philadelphia, Pennsylvania; Providence, RI; Charleston, South Carolina; Sioux Falls, South Dakota; Memphis, Tennessee; Salt Lake City, Utah; Richmond, VA; Seattle, Washington; Charleston, WV; Green Bay, Wisconsin; Jackson, Wyoming; Jacksonville, FL; Key West, FL; Orlando, FL; Panama City, FL; Pensacola, FL; St. Petersburg, FL; Sarasota, Florida; Tampa, Fl; West Palm Beach, FL; Clearwater, Fl; South Beach, FL; Daytona Beach, FL; Fort Lauderdale, FL; Fort Meyers, FL, Fort Walton Beach, FL; Gainesville, FL
Flame Safe SHINGLE SAFE® f/k/a AD108 is an exterior aqueous based resin fire retardant coating formulated primarily for wood shake shingle roofs and other exterior wood substrates. Test at Western Fire Center classified it as an exterior ASTM E108 Class B fire retardant coating for wood shake shingles. ASTM E108 tests at Southwest Research Institute (Burning brand, Flying Brand, Spread of Flame, Intermittent Flame Exposure) after the ASTM E108 5 year Accelerated Weathering Procedure classified SHINGLE SAFE® as an ASTM E108 Class C exterior fire retardant coating with a coverage rate 120-140 sq. ft. /gallon applied by spray. Available in 55 gallon drums
Flame Safe Advantage
*Quick and easy application / *Odorless - Colorless - Non Toxic / *Contains no PDBEs
*Adds no appreciable weight / *Requires no special cutting tools / *Reduces smoke generation
*Fungus inhibitor / *Resistent to insects, Rodents,and certain molds / *Will not harm plants or animals
*Termite resistant
FLAME SAFE PRODUCTS
Applying fire retardant to wood roof
Fire retardant spray for attic area
ORDER FACTORY DIRECT SAVE WITH DAILY DISCOUNTS
Flame Safe Chemical Corporation is the only fire retardant coatings manufacturer designated by The Federal Emergency Management Agency (FEMA) as a partner under the Project Impact Program. The mission of Project Impact and the partnership with Flame Safe Chemical Corporation is to prevent or to mitigate the loss of lives, property and economic impact caused by fire hazard events. Experience has shown that all of Flame Safe’s products are suitable to achieve this endeavor.
FOR OPTIMUM RESULTS, to inhibit or drastically reduce the wind tunnel or blow torch effect of fire in the attic area, treat the underside of the roof in the attic, as well as all other attic substrates, including blown insulation, with Shingle Safe.
PARTNER
